Seat Leon III (5F)

Steps

1. 19 – Gateway → Installation list: enable [6C - Rearview Camera] (for the High camera)
2. 5F – Infotainment → Adaptation
3. Find the Parkingsystem / Bus_Electronics channel
4. Set Byte_18_Rear_View_Camera → Active
5. Restart the 5F head unit (hold the button for 10 sec)

Steps

1. After installing the sensors and receiver unit: 19 – Gateway → add [65 - Tire Pressure]
2. 17 – Instrument Cluster → Coding → TPMS Installed
3. 5F – Infotainment → Adaptation → enable BAP tire_pressure_system_0x07

Steps

1. Replace the gauge cluster and route the MOST optical cable from the 5F module
2. Remove component protection and re-teach the immobiliser using ODIS Online access
3. 5F → Adaptation → Navigation map display switch (enable MOST)

Steps

1. Install the steering-wheel buttons and the radar in the front grille
2. 19 – Gateway → enable [13 - Auto Distance Regulation]
3. 16 – Steering Column → Coding → Cruise Control Installed
4. Upload SWaP licence codes (ODIS)

Steps

1. 19 – Gateway → enable [6D - Trunk Electrics]
2. 09 – Central Electrics → Adaptation → Remote open/close tailgate enable

Steps

1. 09 – Central Electrics → Adaptation → Interior light configuration
2. Upload the Lichtfeld 1-30 RGB values
3. 5F → Adaptation → interieur_light_0x08 → Active

Steps

1. 09 – Central Electrics → Adaptation
2. Activate the Leaving Home and Coming Home channels and set the duration (0–60 sec)

Steps

1. 09 – Central Electrics → Adaptation → enable Comfort opening/closing

Steps

1. 17 – Instrument Cluster → Adaptation → Staging / Indicator Celebration → Active

Steps

1. Connect to the 09 – Central Electrics control unit.
2. In the adaptation menu, find the cornering light channel.
3. Switch it active, and if there's a threshold setting, set the speed limit.
4. Test it stationary: turning the wheel should switch on the light on the correct side.

Steps

1. Connect to the 09 – Central Electrics control unit (on some models this also sits on the 42/52 door control unit).
2. In the adaptation menu, find the mirror-fold channel.
3. Switch on folding linked to locking.
4. Lock the car and check that both mirrors move.

Steps

1. Connect to the 09 – Central Electrics control unit.
2. In the adaptation menu, find the emergency brake light channel.
3. Choose the mode you want: flashing brake light or automatic hazard lights.
4. After saving, test it on an open road with no traffic around.

Steps

1. Connect to the 09 – Central Electrics control unit.
2. In the adaptation menu, find the auto-lock channel.
3. Turn on both locking and unlocking-on-ignition-off.
4. Test it: you should hear the locks click as you pull away.

Steps

1. Switch off the ignition and return the wiper stalk to its resting position.
2. Connect to the 09 – Central Electrics control unit.
3. In the adaptation menu, find the service position channel.
4. Once activated, the arms lift up; turning the ignition back on returns them to normal.

Steps

1. Note down the new battery's data: capacity (Ah), manufacturer, technology (AGM or EFB), and its letter code.
2. Connect to the 19 – Gateway control unit.
3. In the adaptation menu, find the battery-change channels.
4. Enter the capacity, technology, and serial number, then save.

Steps

1. Connect to the 17 – Instrument Cluster control unit.
2. In the adaptation menu, find the digital speed display channel.
3. Switch it active and save.
4. In the display's menu, select the new view that has just appeared.

Steps

1. Fit the cruise control switch and verify the steering-wheel module's signals with a measurement.
2. Connect to the 01 – Engine Control Unit.
3. Long coding: enable the cruise control (GRA) bit.
4. Clear the fault codes, then test above 30 km/h.

Steps

1. Check whether the car has the factory Drive Profile function.
2. Connect to the relevant control unit and save the original coding.
3. Long coding: enable the missing modes.

Steps

1. 19 – Gateway → enable [6D - Trunk Electrics].
2. 09 – Central Electrics → Adaptation → Remote open/close tailgate enable.